Quick Answer: How Much Does It Cost To Have A Well Shocked?

How often should you add bleach to your well?

4) Work out how much bleach will be needed: For every 50 gallons of water in the well use one quart of laundry bleach – (4 quarts in a gallon).

Do not use excessive amounts of bleach – more is not more effective.

5) For best results the bleach should be combined with water before adding it to the well..

What happens if you drink water with too much chlorine?

Chlorine poisoning can cause symptoms throughout your body. Respiratory symptoms include coughing, difficulty breathing, and fluid inside the lungs. Digestive system symptoms include: burning in the mouth.

When can I shower after shocking well?

Before you chlorinate your well, there are a number of precautions and steps to take to ensure safety for your family. Keep in mind that doing laundry and taking a shower cannot be done for at least 24 hours with a chlorinated well. Waiting a few days to do these is a good idea.

How long should you wait to use water after you chlorinate a well?

Let the chlorinated water stand in the plumbing system for 12 to 24 hours. Do not run any water or flush toilets during this time. Use your reserves of fresh water for all purposes. Step 6 WAIT at least 12 hours before turning faucets back on.

Does rain fill your well?

YES! Rainfall has a direct impact on the local water table, which may immediately impact your residential well if it is supplied by shallow aquifers. … Your well may not ‘fill up’ when it rains, but it does reap the indirect benefits.

Can I pour bleach down my well?

Chlorinate the well. Ⅰ Use household bleach which typically has a chlorine concentration of 6%. … Ⅰ Mix bleach in a bucket of water. Remove well cap, plug, or vent (see diagrams on page 2); using a funnel, pour the bleach into your well.

How long does it take to smell chlorine after shocking well?

It can take 30 minutes to 24 hours or more to flush all of the chlorine from the well. ►Once the chlorine is gone from the well, open up each fixture one at a time until the chlorine smell is no longer present. This will purge the remaining chlorine from the water system.

How long does it take for a well to clear up?

between 1 and 2 weeksAll in all, with all steps considered, it will typically take between 1 and 2 weeks to have a new well completely up and running. Of course, depending on several factors, it could take shorter or longer than this.

What happens when your well runs out of water?

Tap water may look muddy or murky or the taste might change. Spigots might cough and sputter as air comes through the line instead of water. The submersible pump may be pumping nothing but air. … The only sure way to tell if the well has run dry is to measure the water level in the well.

Can I shock my own well?

Shock chlorination will be most effective if the chlorine reaches every part of the water system. … One gallon of bleach will treat up to an 8-inch diameter well containing 100 feet of water. If your well is much larger, or if your distribution system is unusually large, expect to use more than 1 gallon of bleach.

How often should you chlorinate your well?

Have a professional check your well water every three to five years to ensure it’s free of dangerous microbes. If their tests do reveal the presence of microbes, order a complete well chlorination. Chlorine treatment will remove all toxic bacteria and algae, with only minimal disruption to your water supply.

How long does shocking a well last?

12 to 24 hoursIf a strong chlorine odor cannot be detected at each faucet and toilet, pour an additional 3 pints of bleach into the well and try again. FLUSH AND FINISH: Turn the pump circuit breaker off, return the well cap or put the cover back in place. Allow chlorinated water to remain in the system for 12 to 24 hours.

Is it safe to drink water that smells like chlorine?

The smell of bleach in your tap water is likely caused by high levels of chlorine. Small traces of chlorine in your water is not harmful. … The EPA requires chlorine in public water systems but recommends levels below 4mg/L. Chlorine can be smelled at levels of 1mg/L.

How long does it take for water to clear after shocking a well?

4 to 8 hoursIt will usually take 4 to 8 hours to flush the well after a standard well chlorination. The water may become discolored during flushing because the chlorine may have loosened the hard water deposits in the plumbing. Caution: The chlorine must be completely flushed from plumbing system.

How can you tell if your well is low?

Warning Signs your Water Well may be Running DrySIGNS YOUR WELL HAS RUN DRY. Your property’s water well may be suffering from drought conditions and drying up if you notice one of these common symptoms:A Change In Taste. … Murky or Muddy Water. … Pump Runs Longer. … Faucets Begin Sputtering. … Neighbors Also Report Water Problems. … HOW TO FIX A DRY WELL. … HELPFUL TIPS.More items…

How do you know if your well pump is going out?

How to tell if your well pump is going bad:No water flow from faucets.Poor water pressure.Constantly running pump.

Can I put chlorine tablets in my well?

Chlorine granules, tablets and liquid chlorine in the form of household bleach can all be used to disinfect your well. … This information should appear on the well log. Measure how much water is standing in the borehole of the well. Step 2 Prepare a solution using unscented liquid household bleach or chlorine granules.

How often should a well be shocked?

every 3 to 5 yearsHomeowners with private wells should have their well water tested every 3 to 5 years for some contaminants, including bacteria. If these tests turn up positive for bacteria, chlorinating the well may be a way to resolve the problem.